View M4T32-BR12SH_1269717.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M41ST85Y M41ST85W
5.0 or 3.0V, 512 bit (64 x 8) Serial RTC and NVRAM Supervisor
FEATURES SUMMARY

5.0 OR 3.0V OPERATING VOLTAGE SERIAL INTERFACE SUPPORTS I2C BUS (400 KHz) NVRAM SUPERVISOR FOR EXTERNAL LPSRAM OPTIMIZED FOR MINIMAL INTERCONNECT TO MCU 2.5 TO 5.5V OSCILLATOR OPERATING VOLTAGE AUTOMATIC SWITCH-OVER AND DESELECT CIRCUITRY CHOICE OF POWER-FAIL DESELECT VOLTAGES - M41ST85Y: VCC = 4.5 to 5.5V; 4.20V VPFD 4.50V - M41ST85W: VCC = 2.7 to 3.6V; 2.55V VPFD 2.70V 1.25V REFERENCE (for PFI/PFO) COUNTERS FOR TENTHS/HUNDREDTHS OF SECONDS, SECONDS, MINUTES, HOURS, DAY, DATE, MONTH, YEAR, AND CENTURY 44 BYTES OF GENERAL PURPOSE RAM PROGRAMMABLE ALARM AND INTERRUPT FUNCTION (VALID EVEN DURING BATTERY BACK-UP MODE) WATCHDOG TIMER MICROPROCESSOR POWER-ON RESET BATTERY LOW FLAG POWER-DOWN TIMESTAMP (HT BIT) ULTRA-LOW BATTERY SUPPLY CURRENT OF 500nA (MAX) PACKAGING INCLUDES A 28-LEAD SOIC AND SNAPHAT(R) TOP (to be ordered separately) SOIC SNAPHAT PACKAGE PROVIDES DIRECT CONNECTION FOR A SNAPHAT TOP WHICH CONTAINS THE BATTERY AND CRYSTAL SOIC EMBEDDED CRYSTAL PACKAGE (MX) OPTION
Figure 1. 28-pin SOIC Package
SNAPHAT (SH) Battery & Crystal
28 1
SOH28 (MH)
Figure 2. 28-pin (300mil) SOIC Package
EMBEDDED Crystal
SOX28 (MX)
September 2004
1/34
M41ST85Y, M41ST85W
TABLE OF CONTENTS
FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 1. 28-pin SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. 28-pin (300mil) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SUMMARY DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 3. Table 1. Figure 4. Figure 5. Figure 6. Figure 7. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-pin SOIC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-pin, 300mil SOIC (MX) Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...... ...... ...... ...... ...... ...... .....5 .....5 .....5 .....5 .....6 .....7
OPERATING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2-Wire Bus Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 8. Serial Bus Data Transfer Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 9. Acknowledgement Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 10.WRITE Cycle Timing: RTC & External SRAM Control Signals . . . . . . . . . . . . . . . . . . . . . 9 READ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 11.Slave Address Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 12.READ Mode Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 13.Alternate READ Mode Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 WRITE Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 14.WRITE Mode Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Data Retention Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 CLOCK OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Power-down Time-Stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 TIMEKEEPER(R) Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 2. TIMEKEEPER (R) Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Calibrating the Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 15.Crystal Accuracy Across Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 16.Calibration Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setting Alarm Clock Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 17.Alarm Interrupt Reset Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 3. Alarm Repeat Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 18.Back-Up Mode Alarm Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Square Wave Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 4. Square Wave Output Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Power-on Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Reset Inputs (RSTIN1 & RSTIN2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 19.RSTIN1 & RSTIN2 Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Table 5. Reset AC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2/34
M41ST85Y, M41ST85W
Power-fail INPUT/OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Century Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Output Driver Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Battery Low Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 trec Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Initial Power-on Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 6. trec Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 7. Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 8. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 DC and AC PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Table 9. DC and AC Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 20.AC Testing Input/Output Waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Table 10. Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Table 11. DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 21.Bus Timing Requirements Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 12. AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 22.Power Down/Up Mode AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 13. Power Down/Up AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 PACKAGE MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 23.SOH28 - 28-lead Plastic Small Outline, Battery SNAPHAT, Package Outline . . . . . . . . 28 Table 14. SOH28 - 28-lead Plastic Small Outline, battery SNAPHAT, Package Mechanical Data 28 Figure 24.SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal, Package Outline . . . . . . . 29 Table 15. SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal, Mechanical Data . . . . . . . 29 Figure 25.SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Package Outline . . . . . . 30 Table 16. SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Mechanical Data . . . . . . 30 Figure 26.SOX28 - 28-lead Plastic Small Outline, 300mils, Embedded Crystal, Package Outline. 31 Table 17. SOX28 - 28-lead Plastic Small Outline, 300mils, Embedded Crystal, Mech. Data. . . . . 31 PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Table 18. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Table 19. SNAPHAT Battery Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 20. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3/34
M41ST85Y, M41ST85W
SUMMARY DESCRIPTION
The M41ST85Y/W Serial TIMEKEEPER(R)/Controller SRAM is a low power 512-bit, static CMOS SRAM organized as 64 words by 8 bits. A built-in 32.768 kHz oscillator (external crystal controlled) and 8 bytes of the SRAM (see Table 2., page 14) are used for the clock/calendar function and are configured in binary coded decimal (BCD) format. An additional 12 bytes of RAM provide status/control of Alarm, Watchdog and Square Wave functions. Addresses and data are transferred serially via a two line, bi-directional I2C interface. The built-in address register is incremented automatically after each WRITE or READ data byte. The M41ST85Y/W has a built-in power sense circuit which detects power failures and automatically switches to the battery supply when a power failure occurs. The energy needed to sustain the SRAM and clock operations can be supplied by a small lithium button-cell supply when a power failure occurs. Functions available to the user include a non-volatile, time-of-day clock/calendar, Alarm interrupts, Watchdog Timer and programmable Square Wave output. Other features include a Power-On Reset as well as two additional debounced inputs (RSTIN1 and RSTIN2) which can also generate an output Reset (RST). The eight clock address locations contain the century, year, month, date, day, hour, minute, second and tenths/hundredths of a second in 24 hour BCD format. Corrections for 28, 29 (leap year - valid until year 2100), 30 and 31 day months are made automatically. The M41ST85Y/W is supplied in a 28-lead SOIC SNAPHAT(R) package (which integrates both crystal and battery in a single SNAPHAT top) or a 28pin, 300mil SOIC package (MX) which includes an embedded 32kHz crystal. The 28-pin, 330mil SOIC provides sockets with gold plated contacts at both ends for direct connection to a separate SNAPHAT housing containing the battery and crystal. The unique design allows the SNAPHAT battery/crystal package to be mounted on top of the SOIC package after the completion of the surface mount process. Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surface-mounting. The SNAPHAT housing is also keyed to prevent reverse insertion. The SOIC and battery/crystal packages are shipped separately in plastic anti-static tubes or in Tape & Reel form. For the 28-lead SOIC, the battery/crystal package (e.g., SNAPHAT) part number is "M4TXX-BR12SH" (see Table 19., page 32). Caution: Do not place the SNAPHAT battery/crystal top in conductive foam, as this will drain the lithium button-cell battery. The 300mil, embedded crystal SOIC requires only a user-supplied battery to provide non-volatile operation.
4/34
M41ST85Y, M41ST85W
Figure 3. Logic Diagram
VCC VBAT (1)
Table 1. Signal Names
ECON EX IRQ/FT/OUT Conditioned Chip Enable Output External Chip Enable Interrupt/Frequency Test/Out Output (Open Drain) Power Fail Input Power Fail Output Reset Output (Open Drain) Reset 1 Input Reset 2 Input Serial Clock Input Serial Data Input/Output Square Wave Output Watchdog Input Supply Voltage Voltage Output Ground Battery Supply Voltage No Connect No Function
SCL ECON SDA RST EX RSTIN1 RSTIN2 PFO WDI VOUT PFI M41ST85Y M41ST85W IRQ/FT/OUT SQW
PFI PFO RST RSTIN1 RSTIN2 SCL SDA SQW WDI VCC VOUT
VSS
VSS
AI03658
VBAT(1) NC NF
Note: 1. For 28-pin, 300mil embedded crystal SOIC only.
Note: 1. For 28-pin, 300mil embedded crystal SOIC only.
Figure 4. 28-pin SOIC Connections
SQW NC NC NC NC NC NC WDI RSTIN1 RSTIN2 NC NC PFO VSS 28 1 2 27 3 26 4 25 5 24 6 23 7 M41ST85Y 22 8 M41ST85W 21 9 20 10 19 11 18 12 17 13 16 14 15
AI03659
Figure 5. 28-pin, 300mil SOIC (MX) Connections
NF NF NF NF NC NC NC SQW WDI RSTIN1 RSTIN2 PFO NC VSS 28 1 2 27 3 26 4 25 5 24 6 23 7 M41ST85Y 22 8 M41ST85W 21 9 20 10 19 11 18 12 17 13 16 14 15 VCC EX IRQ/FT/OUT VOUT NC PFI SCL NC NC RST NC SDA ECON VBAT
AI06370d
VCC EX IRQ/FT/OUT VOUT NC NC PFI NC SCL NC RST NC SDA ECON
Note: No Function (NF) pins should be tied to VSS. Pins 1, 2, 3, and 4 are internally shorted together.
5/34
M41ST85Y, M41ST85W
Figure 6. Block Diagram
REAL TIME CLOCK CALENDAR SDA I2C INTERFACE SCL 44 BYTES USER RAM RTC w/ALARM & CALIBRATION WATCHDOG SQUARE WAVE AFE WDS IRQ/FT/OUT(1)
(2) Crystal
32KHz OSCILLATOR
SQW
WDI VCC
VOUT
VBAT VBL= 2.5V COMPARE BL
VSO = 2.5V
COMPARE
VPFD = 4.4V RSTIN1 RSTIN2
COMPARE
POR RST(1)
(2.65V for ST85W)
EX PFI COMPARE 1.25V (Internal)
ECON PFO
AI03932
Note: 1. Open drain output 2. Integrated into SOIC package for MX package option.
6/34
M41ST85Y, M41ST85W
Figure 7. Hardware Hookup
Regulator Unregulated Voltage VIN VCC
M41ST85Y/W VCC VOUT ECON EX From MCU SCL WDI RSTIN1 SDA RST SQW PFO PFI VBAT VSS (1) IRQ/FT/OUT To RST To LED Display To NMI To INT VCC E M68Z128Y/W or M68Z512Y/W
R1
Pushbutton Reset
RSTIN2
R2
AI03660
Note: 1. Required for embedded crystal (MX) package only.
7/34
M41ST85Y, M41ST85W
OPERATING MODES
The M41ST85Y/W clock operates as a slave device on the serial bus. Access is obtained by implementing a start condition followed by the correct slave address (D0h). The 64 bytes contained in the device can then be accessed sequentially in the following order: 1. Tenths/Hundredths of a Second Register 2. Seconds Register 3. Minutes Register 4. Century/Hours Register 5. Day Register 6. Date Register 7. Month Register 8. Year Register 9. Control Register 10. Watchdog Register 11 - 16. Alarm Registers 17 - 19. Reserved 20. Square Wave Register 21 - 64. User RAM The M41ST85Y/W clock continually monitors VCC for an out-of-tolerance condition. Should VCC fall below VPFD, the device terminates an access in progress and resets the device address counter. Inputs to the device will not be recognized at this time to prevent erroneous data from being written to the device from a an out-of-tolerance system. When VCC falls below VSO, the device automatically switches over to the battery and powers down into an ultra low current mode of operation to conserve battery life. As system power returns and VCC rises above VSO , the battery is disconnected, and the power supply is switched to external VCC. Write protection continues until VCC reaches VPFD(min) plus trec (min). For more information on Battery Storage Life refer to Application Note AN1012. 2-Wire Bus Characteristics The bus is intended for communication between different ICs. It consists of two lines: a bi-directional data signal (SDA) and a clock signal (SCL). Both the SDA and SCL lines must be connected to a positive supply voltage via a pull-up resistor. The following protocol has been defined: - Data transfer may be initiated only when the bus is not busy. - During data transfer, the data line must remain stable whenever the clock line is High. - Changes in the data line, while the clock line is High, will be interpreted as control signals. Accordingly, the following bus conditions have been defined: Bus not busy. Both data and clock lines remain High. Start data transfer. A change in the state of the data line, from High to Low, while the clock is High, defines the START condition. Stop data transfer. A change in the state of the data line, from Low to High, while the clock is High, defines the STOP condition. Data Valid. The state of the data line represents valid data when after a start condition, the data line is stable for the duration of the high period of the clock signal. The data on the line may be changed during the Low period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a start condition and terminated with a stop condition. The number of data bytes transferred between the start and stop conditions is not limited. The information is transmitted byte-wide and each receiver acknowledges with a ninth bit. By definition a device that gives out a message is called "transmitter," the receiving device that gets the message is called "receiver." The device that controls the message is called "master." The devices that are controlled by the master are called "slaves." Acknowledge. Each byte of eight bits is followed by one Acknowledge Bit. This Acknowledge Bit is a low level put on the bus by the receiver whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed is obliged to generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is a stable Low during the High period of the acknowledge related clock pulse. Of course, setup and hold times must be taken into account. A master receiver must signal an end of data to the slave transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this case the transmitter must leave the data line High to enable the master to generate the STOP condition.
8/34
M41ST85Y, M41ST85W
Figure 8. Serial Bus Data Transfer Sequence
DATA LINE STABLE DATA VALID
CLOCK
DATA
START CONDITION
CHANGE OF DATA ALLOWED
STOP CONDITION
AI00587
Figure 9. Acknowledgement Sequence
START SCL FROM MASTER 1 2 8 CLOCK PULSE FOR ACKNOWLEDGEMENT 9
DATA OUTPUT BY TRANSMITTER
MSB
LSB
DATA OUTPUT BY RECEIVER
AI00601
Figure 10. WRITE Cycle Timing: RTC & External SRAM Control Signals
EX tEXPD tEXPD ECON
AI03663
9/34
M41ST85Y, M41ST85W
READ Mode In this mode the master reads the M41ST85Y/W slave after setting the slave address (see Figure 11., page 10). Following the WRITE Mode Control Bit (R/W=0) and the Acknowledge Bit, the word address 'An' is written to the on-chip address pointer. Next the START condition and slave address are repeated followed by the READ Mode Control Bit (R/W=1). At this point the master transmitter becomes the master receiver. The data byte which was addressed will be transmitted and the master receiver will send an Acknowledge Bit to the slave transmitter. The address pointer is only incremented on reception of an Acknowledge Clock. The M41ST85Y/W slave transmitter will now place the data byte at address An+1 on the bus, the master receiver reads and acknowledges the new byte and the address pointer is incremented to An+2. Figure 11. Slave Address Location
R/W
This cycle of reading consecutive addresses will continue until the master receiver sends a STOP condition to the slave transmitter (see Figure 12., page 10). The system-to-user transfer of clock data will be halted whenever the address being read is a clock address (00h to 07h). The update will resume either due to a Stop Condition or when the pointer increments to a non-clock or RAM address. Note: This is true both in READ Mode and WRITE Mode. An alternate READ Mode may also be implemented whereby the master reads the M41ST85Y/W slave without first writing to the (volatile) address pointer. The first address that is read is the last one stored in the pointer (see Figure 13., page 11).
START
SLAVE ADDRESS
A
MSB
1
1
0
1
0
0
LSB 0
AI00602
Figure 12. READ Mode Sequence
START START R/W
BUS ACTIVITY: MASTER
SDA LINE
S
WORD ADDRESS (An)
S
R/W
DATA n
DATA n+1
ACK
ACK
ACK
ACK
BUS ACTIVITY: SLAVE ADDRESS
SLAVE ADDRESS
DATA n+X
P
AI00899
10/34
NO ACK
STOP
ACK
M41ST85Y, M41ST85W
Figure 13. Alternate READ Mode Sequence
START STOP DATA n ACK ACK DATA n+1 ACK ACK DATA n+X P NO ACK
AI00895
BUS ACTIVITY: MASTER SDA LINE
S
BUS ACTIVITY: SLAVE ADDRESS
WRITE Mode In this mode the master transmitter transmits to the M41ST85Y/W slave receiver. Bus protocol is shown in Figure 14., page 11. Following the START condition and slave address, a logic '0' (R/ W=0) is placed on the bus and indicates to the addressed device that word address An will follow and is to be written to the on-chip address pointer. The data word to be written to the memory is Figure 14. WRITE Mode Sequence
START
R/W
strobed in next and the internal address pointer is incremented to the next memory location within the RAM on the reception of an acknowledge clock. The M41ST85Y/W slave receiver will send an acknowledge clock to the master transmitter after it has received the slave address (see Figure 11., page 10) and again after it has received the word address and each data byte.
BUS ACTIVITY: MASTER
R/W
SDA LINE
S
WORD ADDRESS (An)
ACK ACK
DATA n
DATA n+1
DATA n+X
P
ACK
ACK
BUS ACTIVITY: SLAVE ADDRESS
AI00591
ACK
STOP
11/34
M41ST85Y, M41ST85W
Data Retention Mode With valid VCC applied, the M41ST85Y/W can be accessed as described above with READ or WRITE Cycles. Should the supply voltage decay, the M41ST85Y/W will automatically deselect, write protecting itself (and any external SRAM) when VCC falls between VPFD(max) and VPFD(min). This is accomplished by internally inhibiting access to the clock registers. At this time, the Reset pin (RST) is driven active and will remain active until VCC returns to nominal levels. External RAM access is inhibited in a similar manner by forcing ECON to a high level. This level is within 0.2 volts of the VBAT. ECON will remain at this level as long as VCC remains at an out-of-tolerance condition. When VCC falls below the Battery Back-up Switchover Voltage (VSO), power input is switched from the VCC pin to the SNAPHAT(R) battery, and the clock registers and external SRAM are maintained from the attached battery supply. All outputs become high impedance. The VOUT pin is capable of supplying 100 A of current to the attached memory with less than 0.3 volts drop under this condition. On power up, when VCC returns to a nominal value, write protection continues for trec by inhibiting ECON. The RST signal also remains active during this time (see Figure 22., page 27). Note: Most low power SRAMs on the market today can be used with the M41ST85Y/W RTC SUPERVISOR. There are, however some criteria which should be used in making the final choice of
an SRAM to use. The SRAM must be designed in a way where the chip enable input disables all other inputs to the SRAM. This allows inputs to the M41ST85Y/W and SRAMs to be "Don't Care" once VCC falls below VPFD(min). The SRAM should also guarantee data retention down to VCC=2.0 volts. The chip enable access time must be sufficient to meet the system needs with the chip enable output propagation delays included. If the SRAM includes a second chip enable pin (E2), this pin should be tied to VOUT. If data retention lifetime is a critical parameter for the system, it is important to review the data retention current specifications for the particular SRAMs being evaluated. Most SRAMs specify a data retention current at 3.0 volts. Manufacturers generally specify a typical condition for room temperature along with a worst case condition (generally at elevated temperatures). The system level requirements will determine the choice of which value to use. The data retention current value of the SRAMs can then be added to the IBAT value of the M41ST85Y/W to determine the total current requirements for data retention. The available battery capacity for the SNAPHAT(R) of your choice can then be divided by this current to determine the amount of data retention available (see Table 19., page 32). For a further more detailed review of lifetime calculations, please see Application Note AN1012.
12/34
M41ST85Y, M41ST85W
CLOCK OPERATION
The eight byte clock register (see Table 2., page 14) is used to both set the clock and to read the date and time from the clock, in a binary coded decimal format. Tenths/Hundredths of Seconds, Seconds, Minutes, and Hours are contained within the first four registers. Note: A WRITE to any clock register will result in the Tenths/Hundredths of Seconds being reset to "00," and Tenths/Hundredths of Seconds cannot be written to any value other than "00." Bits D6 and D7 of Clock Register 03h (Century/ Hours Register) contain the CENTURY ENABLE Bit (CEB) and the CENTURY Bit (CB). Setting CEB to a '1' will cause CB to toggle, either from '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0,' CB will not toggle. Bits D0 through D2 of Register 04h contain the Day (day of week). Registers 05h, 06h, and 07h contain the Date (day of month), Month and Years. The ninth clock register is the Control Register (this is described in the Clock Calibration section). Bit D7 of Register 01h contains the STOP Bit (ST). Setting this bit to a '1' will cause the oscillator to stop. If the device is expected to spend a significant amount of time on the shelf, the oscillator may be stopped to reduce current drain. When reset to a '0' the oscillator restarts within one second. The eight Clock Registers may be read one byte at a time, or in a sequential block. The Control Register (Address location 08h) may be accessed independently. Provision has been made to assure that a clock update does not occur while any of the eight clock addresses are being read. If a clock address is being read, an update of the clock registers will be halted. This will prevent a transition of data during the READ. Power-down Time-Stamp When a power failure occurs, the Halt Update Bit (HT) will automatically be set to a '1.' This will prevent the clock from updating the TIMEKEEPER (R) registers, and will allow the user to read the exact time of the power-down event. Resetting the HT Bit to a '0' will allow the clock to update the TIMEKEEPER registers with the current time. For more information, see Application Note AN1572. TIMEKEEPER (R) Registers The M41ST85Y/W offers 20 internal registers which contain Clock, Alarm, Watchdog, Flag, Square Wave and Control data. These registers are memory locations which contain external (user accessible) and internal copies of the data (usually referred to as BiPORTTM TIMEKEEPER cells). The external copies are independent of internal functions except that they are updated periodically by the simultaneous transfer of the incremented internal copy. The internal divider (or clock) chain will be reset upon the completion of a WRITE to any clock address. The system-to-user transfer of clock data will be halted whenever the address being read is a clock address (00h to 07h). The update will resume either due to a Stop Condition or when the pointer increments to a non-clock or RAM address. TIMEKEEPER and Alarm Registers store data in BCD. Control, Watchdog and Square Wave Registers store data in Binary Format.
13/34
M41ST85Y, M41ST85W
Table 2. TIMEKEEPER(R) Register Map
Data Address D7 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h OUT WDS AFE RPT4 RPT3 RPT2 RPT1 WDF 0 0 0 RS3 ST 0 CEB TR 0 0 CB 0 0 0 0 D6 D5 D4 D3 D2 D1 D0 0.1 Seconds 10 Seconds 10 Minutes 10 Hours 0 10 Date 10M 0 0 0.01 Seconds Seconds Minutes Hours (24 Hour Format) Day of Week Date: Day of Month Month Year Calibration BMB2 Al 10M BMB1 BMB0 RB1 RB0 Function/Range BCD Format Seconds Seconds Minutes Century/Hours Day Date Month Year Control Watchdog Al Month Al Date Al Hour Al Min Al Sec 0 0 0 0 0 Flags Reserved Reserved Reserved SQW 01-12 01-31 00-23 00-59 00-59 00-99 00-59 00-59 0-1/00-23 01-7 01-31 01-12 00-99
10 Years FT BMB4 SQWE RPT5 HT S BMB3 ABE
Alarm Month Alarm Date Alarm Hour Alarm Minutes Alarm Seconds 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
AI 10 Date AI 10 Hour
Alarm 10 Minutes Alarm 10 Seconds AF 0 0 0 RS2 0 0 0 0 RS1 BL 0 0 0 RS0
Keys: S = Sign Bit FT = Frequency Test Bit ST = Stop Bit 0 = Must be set to zero BL = Battery Low Flag (Read only) BMB0-BMB4 = Watchdog Multiplier Bits CEB = Century Enable Bit CB = Century Bit OUT = Output level AFE = Alarm Flag Enable Flag
RB0-RB1 = Watchdog Resolution Bits WDS = Watchdog Steering Bit ABE = Alarm in Battery Back-Up Mode Enable Bit RPT1-RPT5 = Alarm Repeat Mode Bits WDF = Watchdog flag (Read only) AF = Alarm flag (Read only) SQWE = Square Wave Enable RS0-RS3 = SQW Frequency HT = Halt Update Bit TR = trec Bit
14/34
M41ST85Y, M41ST85W
Calibrating the Clock The M41ST85Y/W is driven by a quartz controlled oscillator with a nominal frequency of 32,768 Hz. The devices are tested not exceed +/-35 ppm (parts per million) oscillator frequency error at 25oC, which equates to about +/-1.53 minutes per month. When the Calibration circuit is properly employed, accuracy improves to better than 2 ppm at 25C. The oscillation rate of crystals changes with temperature (see Figure 15., page 16). Therefore, the M41ST85Y/W design employs periodic counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in Figure 16., page 16. The number of times pulses which are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five Calibration Bits found in the Control Register. Adding counts speeds the clock up, subtracting counts slows the clock down. The Calibration Bits occupy the five lower order bits (D4-D0) in the Control Register (08h). These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a Sign Bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or -2.034 ppm of adjustment per calibration step in the calibration register. Assuming that the oscillator is running at exactly 32,768 Hz, each of the 31 increments in the Calibration byte would represent +10.7 or -5.35 seconds per month which corresponds to a total range of +5.5 or -2.75 minutes per month.
Two methods are available for ascertaining how much calibration a given M41ST85Y/W may require. The first involves setting the clock, letting it run for a month and comparing it to a known accurate reference and recording deviation over a fixed period of time. Calibration values, including the number of seconds lost or gained in a given period, can be found in Application Note AN934, "TIMEKEEPER (R) CALIBRATION." This allows the designer to give the end user the ability to calibrate the clock as the environment requires, even if the final product is packaged in a non-user serviceable enclosure. The designer could provide a simple utility that accesses the Calibration byte. The second approach is better suited to a manufacturing environment, and involves the use of the IRQ/FT/OUT pin. The pin will toggle at 512Hz, when the Stop Bit (ST, D7 of 01h) is '0,' the Frequency Test Bit (FT, D6 of 08h) is '1,' the Alarm Flag Enable Bit (AFE, D7 of 0Ah) is '0,' and the Watchdog Steering Bit (WDS, D7 of 09h) is '1' or the Watchdog Register (09h = 0) is reset. Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at the test temperature. For example, a reading of 512.010124 Hz would indicate a +20 ppm oscillator frequency error, requiring a -10 (XX001010) to be loaded into the Calibration Byte for correction. Note that setting or changing the Calibration Byte does not affect the Frequency test output frequency. The IRQ/FT/OUT pin is an open drain output which requires a pull-up resistor to VCC for proper operation. A 500 to10k resistor is recommended in order to control the rise time. The FT Bit is cleared on power-down.
15/34
M41ST85Y, M41ST85W
Figure 15. Crystal Accuracy Across Temperature
Frequency (ppm) 20 0 -20 -40 -60 -80 -100 -120 -140 -160 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 F = K x (T - T )2 O F K = -0.036 ppm/C 0.006 ppm/C TO = 25C 5C
2 2
Temperature C
AI07888
Figure 16. Calibration Waveform
NORMAL
POSITIVE CALIBRATION
NEGATIVE CALIBRATION
AI00594B
16/34
M41ST85Y, M41ST85W
Setting Alarm Clock Registers Address locations 0Ah-0Eh contain the alarm settings. The alarm can be configured to go off at a prescribed time on a specific month, date, hour, minute, or second, or repeat every year, month, day, hour, minute, or second. It can also be programmed to go off while the M41ST85Y/W is in the battery back-up to serve as a system wake-up call. Bits RPT5-RPT1 put the alarm in the repeat mode of operation. Table 3., page 17 shows the possible configurations. Codes not listed in the table default to the once per second mode to quickly alert the user of an incorrect alarm setting. When the clock information matches the alarm clock settings based on the match criteria defined by RPT5-RPT1, the AF (Alarm Flag) is set. If AFE (Alarm Flag Enable) is also set, the alarm condition activates the IRQ/FT/OUT pin as shown in Figure 17., page 17. To disable alarm, write '0' to the Alarm Date Register and to RPT5-RPT1. Note: If the address pointer is allowed to increment to the Flag Register address, an alarm conFigure 17. Alarm Interrupt Reset Waveform
dition will not cause the Interrupt/Flag to occur until the address pointer is moved to a different address. It should also be noted that if the last address written is the "Alarm Seconds," the address pointer will increment to the Flag address, causing this situation to occur. The IRQ/FT/OUT output is cleared by a READ to the Flags Register. A subsequent READ of the Flags Register is necessary to see that the value of the Alarm Flag has been reset to '0.' The IRQ/FT/OUT pin can also be activated in the battery back-up mode. The IRQ/FT/OUT will go low if an alarm occurs and both ABE (Alarm in Battery Back-up Mode Enable) and AFE are set. The ABE and AFE Bits are reset during power-up, therefore an alarm generated during power-up will only set AF. The user can read the Flag Register at system boot-up to determine if an alarm was generated while the M41ST85Y/W was in the deselect mode during power-up. Figure 18., page 18 illustrates the back-up mode alarm timing.
0Eh
0Fh
10h
ACTIVE FLAG
IRQ/FT/OUT
HIGH-Z
AI03664
Table 3. Alarm Repeat Modes
RPT5 1 1 1 1 1 0 RPT4 1 1 1 1 0 0 RPT3 1 1 1 0 0 0 RPT2 1 1 0 0 0 0 RPT1 1 0 0 0 0 0 Alarm Setting Once per Second Once per Minute Once per Hour Once per Day Once per Month Once per Year
17/34
M41ST85Y, M41ST85W
Figure 18. Back-Up Mode Alarm Waveform
VCC VPFD
VSO trec ABE, AFE Bits in Interrupt Register
AF bit in Flags Register
IRQ/FT/OUT HIGH-Z HIGH-Z
AI03920
Watchdog Timer The watchdog timer can be used to detect an outof-control microprocessor. The user programs the watchdog timer by setting the desired amount of time-out into the Watchdog Register, address 09h. Bits BMB4-BMB0 store a binary multiplier and the two lower order bits RB1-RB0 select the resolution, where 00=1/16 second, 01=1/4 second, 10=1 second, and 11=4 seconds. The amount of timeout is then determined to be the multiplication of the five-bit multiplier value with the resolution. (For example: writing 00001110 in the Watchdog Register = 3*1 or 3 seconds). Note: The accuracy of the timer is within the selected resolution. If the processor does not reset the timer within the specified period, the M41ST85Y/W sets the WDF (Watchdog Flag) and generates a watchdog interrupt or a microprocessor reset. The most significant bit of the Watchdog Register is the Watchdog Steering Bit (WDS). When set to a '0,' the watchdog will activate the IRQ/FT/OUT pin when timed-out. When WDS is set to a '1,' the watchdog will output a negative pulse on the RST pin for trec. The Watchdog register, FT, AFE, ABE and SQWE Bits will reset to a '0' at the end of a Watchdog time-out when the WDS Bit is set to a '1.'
The watchdog timer can be reset by two methods: 1) a transition (high-to-low or low-to-high) can be applied to the Watchdog Input pin (WDI) or 2) the microprocessor can perform a WRITE of the Watchdog Register. The time-out period then starts over. Note: The WDI pin should be tied to VSS if not used. In order to perform a software reset of the watchdog timer, the original time-out period can be written into the Watchdog Register, effectively restarting the count-down cycle. Should the watchdog timer time-out, and the WDS Bit is programmed to output an interrupt, a value of 00h needs to be written to the Watchdog Register in order to clear the IRQ/FT/OUT pin. This will also disable the watchdog function until it is again programmed correctly. A READ of the Flags Register will reset the Watchdog Flag (Bit D7; Register 0Fh). The watchdog function is automatically disabled upon power-up and the Watchdog Register is cleared. If the watchdog function is set to output to the IRQ/FT/OUT pin and the frequency test function is activated, the watchdog function prevails and the frequency test function is denied.
18/34
M41ST85Y, M41ST85W
Square Wave Output The M41ST85Y/W offers the user a programmable square wave function which is output on the SQW pin. RS3-RS0 bits located in 13h establish the square wave output frequency. These frequencies are listed in Table 4. Once the selection Table 4. Square Wave Output Frequency
Square Wave Bits RS3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 RS2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 RS1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 RS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Square Wave Frequency None 32.768 8.192 4.096 2.048 1.024 512 256 128 64 32 16 8 4 2 1 Units - kHz kHz kHz kHz kHz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz
of the SQW frequency has been completed, the SQW pin can be turned on and off under software control with the Square Wave Enable Bit (SQWE) located in Register 0Ah.
19/34
M41ST85Y, M41ST85W
Power-on Reset The M41ST85Y/W continuously monitors VCC. When VCC falls to the power fail detect trip point, the RST pulls low (open drain) and remains low on power-up for trec after VCC passes VPFD(max). The RST pin is an open drain output and an appropriate pull-up resistor should be chosen to control rise time. Reset Inputs (RSTIN1 & RSTIN2) The M41ST85Y/W provides two independent inputs which can generate an output reset. The duration and function of these resets is identical to a reset generated by a power cycle. Table 5 and Figure 19 illustrate the AC reset characteristics of this function. Pulses shorter than tRLRH1 and tRLRH2 will not generate a reset condition. RSTIN1 and RSTIN2 are each internally pulled up to VCC through a 100k resistor.
Figure 19. RSTIN1 & RSTIN2 Timing Waveforms
RSTIN1 tRLRH1 RSTIN2 tRLRH2 RST
(1)
tR1HRH
tR2HRH
AI03665
Note: With pull-up resistor
Table 5. Reset AC Characteristics
Symbol tRLRH1(2) tRLRH2(3) tR1HRH(4) tR2HRH(4)
Note: 1. 2. 3. 4.
Parameter(1) RSTIN1 Low to RSTIN1 High RSTIN2 Low to RSTIN2 High RSTIN1 High to RST High RSTIN2 High to RST High
Min 200 100 40 40
Max
Unit ns ms
200 200
ms ms
Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except where noted). Pulse width less than 50ns will result in no RESET (for noise immunity). Pulse width less than 20ms will result in no RESET (for noise immunity). Programmable (see Table 6., page 22).
20/34
M41ST85Y, M41ST85W
Power-fail INPUT/OUTPUT The Power-Fail Input (PFI) is compared to an internal reference voltage (1.25V). If PFI is less than the power-fail threshold (VPFI), the Power-Fail Output (PFO) will go low. This function is intended for use as an undervoltage detector to signal a failing power supply. Typically PFI is connected through an external voltage divider (see Figure 7., page 7) to either the unregulated DC input (if it is available) or the regulated output of the VCC regulator. The voltage divider can be set up such that the voltage at PFI falls below VPFI several milliseconds before the regulated VCC input to the M41ST85Y/W or the microprocessor drops below the minimum operating voltage. During battery back-up, the power-fail comparator turns off and PFO goes (or remains) low. This occurs after VCC drops below VPFD(min). When power returns, PFO is forced high, irrespective of VPFI for the write protect time (trec), which is the time from VPFD(max) until the inputs are recognized. At the end of this time, the power-fail comparator is enabled and PFO follows PFI. If the comparator is unused, PFI should be connected to VSS and PFO left unconnected. Century Bit Bits D7 and D6 of Clock Register 03h contain the CENTURY ENABLE Bit (CEB) and the CENTURY Bit (CB). Setting CEB to a '1' will cause CB to toggle, either from a '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0,' CB will not toggle. Output Driver Pin When the FT Bit, AFE Bit and watchdog register are not set, the IRQ/FT/OUT pin becomes an output driver that reflects the contents of D7 of the Control Register. In other words, when D7 (OUT Bit) and D6 (FT Bit) of address location 08h are a '0,' then the IRQ/FT/OUT pin will be driven low. Note: The IRQ/FT/OUT pin is an open drain which requires an external pull-up resistor. Battery Low Warning The M41ST85Y/W automatically performs battery voltage monitoring upon power-up and at factoryprogrammed time intervals of approximately 24 hours. The Battery Low (BL) Bit, Bit D4 of Flags Register 0Fh, will be asserted if the battery voltage is found to be less than approximately 2.5V. The BL Bit will remain asserted until completion of battery replacement and subsequent battery low monitoring tests, either during the next power-up sequence or the next scheduled 24-hour interval. If a battery low is generated during a power-up sequence, this indicates that the battery is below approximately 2.5 volts and may not be able to maintain data integrity in the SRAM. Data should be considered suspect and verified as correct. A fresh battery should be installed. If a battery low indication is generated during the 24-hour interval check, this indicates that the battery is near end of life. However, data is not compromised due to the fact that a nominal VCC is supplied. In order to insure data integrity during subsequent periods of battery back-up mode, the battery should be replaced. The SNAPHAT top may be replaced while VCC is applied to the device. Note: This will cause the clock to lose time during the interval the SNAPHAT battery/crystal top is disconnected. The M41ST85Y/W only monitors the battery when a nominal VCC is applied to the device. Thus applications which require extensive durations in the battery back-up mode should be powered-up periodically (at least once every few months) in order for this technique to be beneficial. Additionally, if a battery low is indicated, data integrity should be verified upon power-up via a checksum or other technique.
21/34
M41ST85Y, M41ST85W
trec Bit Bit D7 of Clock Register 04h contains the trec Bit (TR). trec refers to the automatic continuation of the deselect time after VCC reaches VPFD. This allows for a voltage settling time before WRITEs may again be performed to the device after a power-down condition. The trec Bit will allow the user to set the length of this deselect time as defined by Table 6., page 22. Table 6. trec Definitions
trec Bit (TR) 0 0 1
Note: 1. Default Setting
Initial Power-on Defaults Upon initial application of power to the device, the following register bits are set to a '0' state: Watchdog Register, FT, AFE, ABE, SQWE, and TR. The following bits are set to a '1' state: ST, OUT, and HT (see Table 7., page 22).
STOP Bit (ST) Min 0 1 X 96 40 50
trec Time Max 98 200(1) 2000
Units ms ms s
Table 7. Default Values
Condition Initial Power-up(2) Subsequent Power-up (with battery back-up)(3) TR 0 UC ST 1 UC HT 1 1 Out 1 UC FT 0 0 AFE 0 0 ABE 0 0 SQWE 0 0 WATCHDOG Register(1) 0 0
Note: 1. WDS, BMB0-BMB4, RB0, RB1. 2. State of other control bits undefined. 3. UC = Unchanged
22/34
M41ST85Y, M41ST85W
MAXIMUM RATING
Stressing the device above the rating listed in the "Absolute Maximum Ratings" table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is Table 8. Absolute Maximum Ratings
Symbol TSTG Parameter Storage Temperature (VCC Off, Oscillator Off) SNAPHAT(R) SOIC Lead-free lead finish(1) TSLD Lead Solder Temperature for 10 seconds Standard (SnPb) lead finish(2,3) Value -40 to 85 -55 to 125 260 240 -0.3 to VCC+0.3 M41ST85Y Supply Voltage M41ST85W Output Current Power Dissipation -0.3 to 4.6 20 1 V mA W -0.3 to 7 Unit C C C C V V
not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents.
VIO VCC IO PD
Input or Output Voltage
Note: 1. For SOH28 package, Lead-free (Pb-free) lead finish: Reflow at peak temperature of 260C (total thermal budget not to exceed 245C for greater than 30 seconds). 2. For SOH28 package, standard (SnPb) lead finish: Reflow at peak temperature of 225C (total thermal budget not to exceed 180C for between 90 to 150 seconds). 3. The SOX28 package has Lead-free (Pb-free) lead finish, but cannot be exposed to peak reflow temperature in excess of 240C (use same reflow profile as standard (SnPb) lead finish).
CAUTION: Negative undershoots below -0.3V are not allowed on any pin while in the Battery Back-up mode. CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets.
23/34
M41ST85Y, M41ST85W
DC AND AC PARAMETERS
This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC Characteristic tables are derived from tests performed under the MeasureTable 9. DC and AC Measurement Conditions
Parameter VCC Supply Voltage Ambient Operating Temperature Load Capacitance (CL) Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages
Note: Output High Z is defined as the point where data is no longer driven.
ment Conditions listed in the relevant tables. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters.
M41ST85Y 4.5 to 5.5V -40 to 85C 100pF 50ns 0.2 to 0.8VCC 0.3 to 0.7VCC
M41ST85W 2.7 to 3.6V -40 to 85C 50pF 50ns 0.2 to 0.8VCC 0.3 to 0.7VCC
Figure 20. AC Testing Input/Output Waveforms
0.8VCC
0.7VCC 0.3VCC
AI02568
0.2VCC
Note: 50pF for M41ST85W.
Table 10. Capacitance
Symbol CIN COUT tLP
(3)
Parameter(1,2) Input Capacitance Output Capacitance Low-pass filter input time constant (SDA and SCL)
Min
Max 7 10 50
Unit pF pF ns
Note: 1. Effective capacitance measured with power supply at 5V. Sampled only, not 100% tested. 2. At 25C, f = 1MHz. 3. Outputs are deselected.
24/34
M41ST85Y, M41ST85W
Table 11. DC Characteristics
Sym Parameter Battery Current OSC ON Battery Current OSC OFF Supply Current Supply Current (Standby) Input Leakage Current ILI(3) Input Leakage Current (PFI) Output Leakage Current 0V VIN VCC VOUT1 > VCC - 0.3V VOUT2 > VBAT - 0.3V 0.7VCC -0.3 2.5 IOH = -1.0mA RST, IRQ/FT/OUT IOUT2 = -1.0A IOL = 3.0mA IOL = 10mA 4.20 VCC = 5V(Y) VCC = 3V(V) PFI Rising 1.225 4.40 1.250 20 2.5 2.5 2.9 2.4 5.5 3.5 0.4 0.4 4.50 1.275 70 2.55 1.225 2.60 1.250 20 2.5 2.5 2.9 3.0 Test Condition(1) TA = 25C, VCC = 0V, VBAT = 3V f = 400kHz SCL, SDA = VCC - 0.3V 0V VIN VCC -25 2 M41ST85Y Min Typ 400 50 1.4 1 1 25 1 175 100 VCC + 0.3 0.3VCC 3.5(9) 0.7VCC -0.3 2.5 2.4 3.6 3.5 0.4 0.4 2.70 1.275 70 3.0 -25 2 Max 500 Min M41ST85W Typ 400 50 0.75 0.50 1 25 1 100 100 VCC + 0.3 0.3VCC 3.5(9) Max 500 nA nA mA mA A nA A mA A V V V V V V V V V V mV V Unit
IBAT
(2)
ICC1 ICC2
ILO(4)
IOUT1(5) VOUT Current (Active) IOUT2 VIH VIL VBAT VOH VOUT Current (Battery Back-up) Input High Voltage Input Low Voltage Battery Voltage Output High Voltage(6) Pull-up Supply Voltage (Open Drain) VOHB(7) VOH (Battery Back-up) Output Low Voltage VOL Output Low Voltage (Open Drain)(8) Power Fail Deselect PFI Input Threshold PFI Hysteresis VSO
Note: 1. 2. 3. 4. 5. 6. 7.
VPFD VPFI
Battery Back-up Switchover
Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except where noted). Measured with VOUT and ECON open. RSTIN1 and RSTIN2 internally pulled-up to VCC through 100K resistor. WDI internally pulled-down to VSS through 100K resistor. Outputs Deselected. External SRAM must match RTC SUPERVISOR chip VCC specification. For PFO and SQW pins (CMOS). Conditioned output (ECON) can only sustain CMOS leakage current in the battery back-up mode. Higher leakage currents will reduce battery life. 8. For IRQ/FT/OUT, RST pins (Open Drain): if pulled-up to supply other than VCC, this supply must be equal to, or less than 3.0V when VCC = 0V (during battery back-up mode). 9. For rechargeable back-up, VBAT (max) may be considered VCC.
25/34
M41ST85Y, M41ST85W
Figure 21. Bus Timing Requirements Sequence
SDA tBUF tHD:STA tR SCL tHIGH P S tLOW tSU:DAT tHD:DAT tSU:STA SR P tSU:STO tF tHD:STA
AI00589
Table 12. AC Characteristics
Symbol fSCL tBUF tEXPD tF tHD:DAT(2) tHD:STA tHIGH tLOW tR tSU:DAT tSU:STA tSU:STO SCL Clock Frequency Time the bus must be free before a new transmission can start EX to ECON Propagation Delay SDA and SCL Fall Time Data Hold Time START Condition Hold Time (after this period the first clock pulse is generated) Clock High Period Clock Low Period SDA and SCL Rise Time Data Setup Time START Condition Setup Time (only relevant for a repeated start condition) STOP Condition Setup Time 100 600 600 0 600 600 1.3 300 M41ST85Y M41ST85W Parameter(1) Min 0 1.3 10 15 300 ns ns s ns ns s ns ns ns ns Max 400 Unit kHz s
Note: 1. Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except where noted). 2. Transmitter must internally provide a hold time to bridge the undefined region (300ns max) of the falling edge of SCL.
26/34
M41ST85Y, M41ST85W
Figure 22. Power Down/Up Mode AC Waveforms
VCC VPFD (max) VPFD (min) VSO tF tFB tPD PFO tDR tRB trec tR
INPUTS
RECOGNIZED
DON'T CARE
RECOGNIZED
RST HIGH-Z OUTPUTS VALID
(PER CONTROL INPUT)
VALID
(PER CONTROL INPUT)
ECON
AI03661
Table 13. Power Down/Up AC Characteristics
Symbol tF(2) tFB(3) tPD tPFD tR tRB trec(4) Parameter(1) VPFD(max) to VPFD(min) VCC Fall Time VPFD(min) to VSS VCC Fall Time EX at VIH before Power Down PFI to PFO Propagation Delay VPFD(min) to VPFD(max) VCC Rise Time VSS to VPFD(min) VCC Rise Time Power up Deselect Time 10 1 40 200 Min 300 10 0 15 25 Typ Max Unit s s s s s s ms
Note: 1. Valid for Ambient Operating Temperature: TA = -40 to 85C; VCC = 4.5 to 5.5V or 2.7 to 3.6V (except where noted). 2. VPFD(max) to VPFD(min) fall time of less than tF may result in deselection/write protection not occurring until 200s after VCC passes VPFD(min). 3. VPFD(min) to VSS fall time of less than tFB may cause corruption of RAM data. 4. Programmable (see Table 6., page 22)
27/34
M41ST85Y, M41ST85W
PACKAGE MECHANICAL INFORMATION
Figure 23. SOH28 - 28-lead Plastic Small Outline, Battery SNAPHAT, Package Outline
A2 B e
A C eB CP
D
N
E
H A1 L
1 SOH-A
Note: Drawing is not to scale.
Table 14. SOH28 - 28-lead Plastic Small Outline, battery SNAPHAT, Package Mechanical Data
Symbol A A1 A2 B C D E e eB H L N CP 1.27 0.05 2.34 0.36 0.15 17.71 8.23 - 3.20 11.51 0.41 0 28 0.10 millimeters Typ Min Max 3.05 0.36 2.69 0.51 0.32 18.49 8.89 - 3.61 12.70 1.27 8 0.050 0.002 0.092 0.014 0.006 0.697 0.324 - 0.126 0.453 0.016 0 28 0.004 Typ inches Min Max 0.120 0.014 0.106 0.020 0.012 0.728 0.350 - 0.142 0.500 0.050 8
28/34
M41ST85Y, M41ST85W
Figure 24. SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal, Package Outline
A1
A2 A A3
eA D
B eB
L
E
SHTK-A
Note: Drawing is not to scale.
Table 15. SH - 4-pin SNAPHAT Housing for 48mAh Battery & Crystal, Mechanical Data
Symbol A A1 A2 A3 B D E eA eB L 0.46 21.21 14.22 15.55 3.20 2.03 6.73 6.48 millimeters Typ Min Max 9.78 7.24 6.99 0.38 0.56 21.84 14.99 15.95 3.61 2.29 0.0181 0.8350 0.5598 0.6122 0.1260 0.0799 0.2650 0.2551 Typ inches Min Max 0.3850 0.2850 0.2752 0.0150 0.0220 0.8598 0.5902 0.6280 0.1421 0.0902
29/34
M41ST85Y, M41ST85W
Figure 25. SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Package Outline
A1
A2 A A3
eA D
B eB
L
E
SHTK-A
Note: Drawing is not to scale.
Table 16. SH - 4-pin SNAPHAT Housing for 120mAh Battery & Crystal, Mechanical Data
Symbol A A1 A2 A3 B D E eA eB L 0.46 21.21 17.27 15.55 3.20 2.03 8.00 7.24 millimeters Typ Min Max 10.54 8.51 8.00 0.38 0.56 21.84 18.03 15.95 3.61 2.29 0.018 0.835 0.680 0.612 0.126 0.080 0.315 0.285 Typ inches Min Max 0.415 0.335 0.315 0.015 0.022 0.860 0.710 0.628 0.142 0.090
30/34
M41ST85Y, M41ST85W
Figure 26. SOX28 - 28-lead Plastic Small Outline, 300mils, Embedded Crystal, Package Outline
D
14 1
h x 45
C E H
15
28
A2 B SO-E
Note: Drawing is not to scale.
A e A1 ddd A1 L
Table 17. SOX28 - 28-lead Plastic Small Outline, 300mils, Embedded Crystal, Mech. Data
Symbol A A1 A2 B C D ddd E e H L N 1.27 7.57 - 10.16 0.51 0 28 millimeters Typ Min 2.44 0.15 2.29 0.41 0.20 17.91 Max 2.69 0.31 2.39 0.51 0.31 18.01 0.10 7.67 - 10.52 0.81 8 0.050 0.298 - 0.400 0.020 0 28 Typ inches Min 0.096 0.006 0.090 0.016 0.008 0.705 Max 0.106 0.012 0.094 0.020 0.012 0.709 0.004 0.302 - 0.414 0.032 8
31/34
M41ST85Y, M41ST85W
PART NUMBERING
Table 18. Ordering Information Scheme
Example: M41ST 85Y MH 6 E
Device Type M41ST
Supply Voltage and Write Protect Voltage 85Y = VCC = 4.5 to 5.5V; 4.20V VPFD 4.50V 85W = VCC = 2.7 to 3.6V; 2.55V VPFD 2.70V
Package MH(1) = SOH28 MX(2) = SOX28
Temperature Range 6 = -40 to 85C
Shipping Method For SOH28: blank = Tubes (Not for New Design - Use E) E = Lead-free Package (ECO F = Lead-free Package (ECO PACK(R)), Tubes PACK(R)), Tape & Reel
TR = Tape & Reel (Not for New Design - Use F) For SOX28: blank = Tubes TR = Tape & Reel
Note: 1. The 28-pin SOIC package (SOH28) requires the SNAPHAT(R) battery/crystal package which is ordered separately under the part number "M4TXX-BR12SHX" in plastic tube or "M4TXX-BR12SHXTR" in Tape & Reel form (see 19). 2. The SOX28 package includes an embedded 32,768Hz crystal. Caution: Do not place the SNAPHAT battery package "M4TXX-BR12SH" in conductive foam as it will drain the lithium button-cell battery.
For other options, or for more information on any aspect of this device, please contact the ST Sales Office nearest you. Table 19. SNAPHAT Battery Table
Part Number M4T28-BR12SH M4T32-BR12SH Description Lithium Battery (48mAh) and Crystal SNAPHAT Lithium Battery (120mAh) and Crystal SNAPHAT Package SH SH
32/34
M41ST85Y, M41ST85W
REVISION HISTORY
Table 20. Document Revision History
Date August 2000 24-Aug-00 12-Oct-00 18-Dec-00 Rev. # 1.0 1.1 1.2 2.0 First issue Block Diagram added (Figure 3) trec Table removed, cross references corrected Reformatted, TOC added, and PFI Input Leakage Current added (Table 11) Addition of trec information, table changed, one added (Tables 2, 6); changed PFI/PFO graphic (see Figure 6); change to DC and AC Characteristics, Order Information (Tables 11, 12, 18); note added to "Setting Alarm Clock Registers" section; added temp./voltage info. to tables (Table 10, 11, 6, 12, 13); addition of Default Values (Table 7) Note added to Clock Operation section Change in Product Maturity Improve text in "Setting the Alarm Clock" section Change VPFD values in document DC Characteristics VBAT changed; VOHB changed; PFI Hysteresis (PFI Rising) spec. added; and Crystal Electrical Characteristics table removed (Tables 11, 6) Changed READ/WRITE Mode Sequences (Figure 12, 14); change in VPFD lower limit for 5V (M41ST85Y) part only (Table 11, 18) Change trec Definition (Table 6); modify reflow time and temperature footnote (Table 8) Modify DC Characteristics table footnote, Default Values (Tables 11, 7) Added embedded crystal (MX) package option; corrected initial power-up condition (Figure 2, 3, 5, 6, 7, 26, Table 1, 7, 18, 17) Update diagrams (Figure 6, 7, 26); update values (Table 13, 5, 6, 7, 17) New Si changes (Table 13, 5, 6); corrected dimensions (Figure 26; Table 17) Reformatted; correct dimensions; update Lead-free information (Figure 22, 15, 18; Table 8, 16, 18) Update characteristics; add package shipping (Figure 5; Table 1, 11, 18) Update Maximum ratings (Table 8) Revision Details
18-Jun-01
2.1
22-Jun-01 26-Jul-01 07-Aug-01 20-Aug-01 06-Sep-01 03-Dec-01 01-May-02 03-Jul-02 15-Nov-02 24-Jan-03 25-Feb-03 20-May-04 15-Jun-04 13-Sep-04
2.2 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 4.0 5.0 6.0 7.0
M41ST85, M41ST85Y, M41ST85W, 41ST85, ST85, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, SUPERVISOR, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, Serial, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, RTC, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, Microprocessor, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, I2C, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Oscillator, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Crystal, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, Alarm, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, IRQ, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFI, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, PFO, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Reset, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Low, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Battery, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Switchover, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Backup, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Power-fail, Powerfail, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, Comparator, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SNAPHAT, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, SOIC, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 5V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V, 3V
33/34
M41ST85Y, M41ST85W
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners (c) 2004 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
34/34

▲Up To Search▲

Price & Availability of M4T32-BR12SH

	To Download M4T32-BR12SH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .